We will talk about Top 10 Best CPU coolers for Ryzen 5 3600 in this post.
AMD’s Ryzen 5 3000 series of processors came out in the middle of 2019. These CPUs are top-of-the-line and made for advanced gaming. AMD Ryzen 5 3600 is one of the CPUs in this generation of AMD Ryzen CPUs that came in different versions.
As you may know, the temperature of the CPU can vary a lot depending on how it is built. High-end CPUs like the Ryzen 5 3600 get very hot, to the point where it could hurt the hardware itself. So, in order to keep their temperatures down, they need a way to cool down.
Be sure to check out our many other buying guides, including the Best AM4 CPU , Best CPU for RTX 2080, Best CPU under $300 , and Best Motherboards for i7 9700K.
The Ryzen 5 3600 is a processor that works very well. It has 12 threads and 6 cores. With a base clock of 3.5GHz that can be overclocked to 4.2GHz, it has a TDP rating of 65W that can change depending on how much you overclock.
So, the Ryzen 5 3600 needs a lot of cooling to keep its temperatures under control. A AMD Wraith Series Cooler is also included with the Ryzen 5 3600. Getting a cooler for your Ryzen 5 3600 may or may not be a good idea, depending on how well it works.
But if you want to buy one, keep reading and we’ll help you decide which one to get.
Ryzen 5 3600 Stock Cooler vs Aftermarket
The stock cooler for the Ryzen 5 3600 CPU chip is made by AMD. Ryzen 5 3600 is cooled by the Wraith Stealth unit, which is part of AMD’s Wraith line.
Unlike Intel, the stock coolers for the Wraith Series, like the Wraith Prism or Wraith Spire, have been known to work well in the past. The Wraith Stealth doesn’t perform as well as these two, but it’s still a good stock cooler.
The Wraith Stealth Cooler is 12.7cm long, 11.2cm wide, and 10.2cm high (L x W x H). As you would expect from a stock cooler, it is small and easy to install. There are no clearance or compatibility issues. With only 38dbA, the noise output is also hard to hear.
It also comes with a 3.81-inch fan and a pre-installed heatsink that works pretty well. So, the cooler isn’t bad at all for base clocks, but it could have done a better job of cooling the 3600 when it was under more stress.
In the end, temperatures are fine for basic use and stock operation, but the cooler doesn’t work as well as it should, even with light overclocking.Ryzen 5 3600 has a lot of room to be overclocked and used to its full potential. The Wraith Stealth isn’t good enough for extreme overclocking, which is a shame.
In the end, the thermal performance just doesn’t measure up. Aftermarket coolers are a must if you want to get the most out of your CPU when you’re playing games.
Our Recommendations for Best CPU coolers for Ryzen 5 3600
Today, we’ll look at the Best CPU coolers for Ryzen 5 3600 that will be on the market in 2023.
|Best Corsair CPU Cooler for Ryzen 5 3600||Check Price|
|High-performing and quiet option for Ryzen 5 3600||Check Price|
|Best Air Cooler for Ryzen 5 3600||Check Price|
|Best budget CPU air cooler for Ryzen 5 3600||Check Price|
|Quietest budget air cooler for Ryzen 5 3600||Check Price|
|Best All-Round Cooler for Ryzen 5 3600||Check Price|
|Best low-profile budget cooler runner-up for Ryzen 5 3600||Check Price|
Corsair Hydro Series H100i
|Noise Level:||38 dB|
|Dimensions:||12.1 x 8.8 x 5.9 inches|
|Fan Speed:||2435 RPM|
We all know the name Corsair, whether it’s for RAM, power supplies, cases, or cooling solutions. Since we’ve come to trust Corsair products over time, it wouldn’t have been fair to leave one out. The Hydro Series H100i from Corsair is one of the best CPU coolers for the Ryzen 5 3600 and is on our list.
The Corsair Hydro H100i is a stylish way to cool your computer with water. The H100i is the perfect AIO for you because it has two of Corsair’s best RGB fans and a 240mm radiator. On the other hand, the Corsair iCUE software takes care of everything.
Since the Corsair Hydro Series H100i has a link monitoring control, your fans will always run at the right speeds, making less noise and keeping the temperature down. Everything on the Corsair H100i has already been set up by the company that made it, so you don’t have to worry about headaches or running out of space.
The Corsair Hydro H100i is a cooler made for people who want to look good and get good performance. Because of its strong 240mm radiator, the Corsair Hydro Seris H100i can handle any CPU that runs hot.
The Corsair H100i’s RGB control is completely in the hands of the user, who can choose from millions of color options. But the Fans can run at a maximum RPM of 2400, which makes them able to handle high temperatures. Thanks to the high quality of the tubing, customers don’t have to worry about leaks.
- RGB color space tuning
- minimal background noise
- Amazing Display
Scythe Mugen 5 Rev.B
|Noise Level:||30 dB|
|Dimensions:||7 x 7 x 6 inches|
|Fan Speed:||1500 RPM|
People do want something that fits their budget, and it’s usually hard to find something that meets everyone’s needs. So, I’ve brought you the best cooler for Ryzen 3600 under $100. The name might turn people off, but if we look at how well it works, it’s out of this world.
Even though the price of the part is low, it still does a great job. The design is sleek, and the heatsink is strong and sturdy, which helps get rid of heat more quickly.
In addition, the fan is very, very quiet. I can promise you that you won’t hear any sounds when you play games on the highest settings. That’s a good thing, isn’t it?
It’s important to note that the cooler is about 154.5mm tall, so you can fit as many RAM modules as you can. In fact, that’s a plus.
The only bad thing happens when you try to put together the parts for an ITX build. Sorry to break it to you, but this cooler won’t work well with your ITX case, so keep that in mind.
The fan comes with an easy-to-follow guide for setting it up. All you have to do is put the heatsink back on top of the processor, and you’re done.
Last but not least, the cooler moves very quickly and is known for bringing down temperatures that are too high. I would say that you are safe. Go ahead and buy it!
- Great airflow
- Decent air pressure
- Looks beautiful
- Simple instructions
- A big no for ITX builds
|Noise Level:||19.2 dB|
|Dimensions:||6.5 x 5.91 x 5.31 inches|
|Fan Speed:||1500 RPM|
The Noctua NH-D15 is, like all Noctua coolers, a work of art. We think the Noctua NH-D15 is a great match for the Ryzen 5 3600 because of how well it works. The Noctua NH-D15 is a dual-tower air cooler with two high-quality Noctua NF-A15 fans that can reach 1500 RPM.
The Noctua NH-D15 comes with two Noctua NF-A15 fans that are 150mm in size. That is, a push-pull fan setup with two fans will keep the temperature in the throat down. The fans come in the beautiful Beige and Brown Noctua colour scheme, which looks stunning on an aluminium body.
The Noctua NH-D15 is great because it has a full aluminium body with great fin density and structure. The 6 heat pipes that are soldered to the fins and copper base plate help get rid of heat as quickly as possible. The build quality is great, which is what you would expect from a company like Noctua.
The SecuFirm2 mounting system is another feature that puts it in the elite class and makes it more popular.
You can control the pressure on the contacts, make sure they are safe and work well, and use it easily and in any socket. The NT-H1 thermal compound from Noctua is used, which has been shown to be a high-quality product.
For dual fan modes, it is best to use RAM with a standard height. In this design, a 32mm RAM that works well with other devices is used. This model is topped off with trusted, professional-grade parts, which makes it the best choice CPU cooler.
- Give help when the temperature is high, even between 50 and 65C while gaming.
- More efficient, less noisy, takes overall less space
- The best cooling system with a warranty of six years
- Why does it cost so much?
- only comes in two colours.
Thermaltake TH360 ARGB
|Noise Level:||28.2 dB|
|Dimensions:||10.51 x 8.47 x 5.39 inches|
|Fan Speed:||1500 RPM|
The Thermaltake TH360 ARGB is a new all-in-one (AIO) liquid cooler from the well-known brand Thermaltake. It’s also the only Ryzen 5 3600 cooler on this list with a 360mm fan. The TH360 came out as a 360mm version of other coolers in the TH series, such as the TH120 and TH240.
The dimensions of the TH360 cooler are 395 x 120 x 52 mm. This AIO has three 120mm fans that spin at up to 1500 RPM and have ARGB lights. It works with any CPU socket up to and including AM4.
Also, the tubes are covered with thick material, and the water block has RGB lighting and a 32dbA noise rating. Even though Thermaltake doesn’t put the thermal paste on for you, they do include some of it in the box. For 360mm AIOs, the TDP is 400W or more.
We compared the TH360 ARGB Sync to the Intel Boxed cooler to see how well they cooled. Both coolers were put to the test in the Fractal Define 7 for realistic and ideal conditions. Everything else was the same, and the speed of the case fan was set. Both tests were done in a room that was 21 °C.
One of the best 360mm AIO liquid coolers on the market right now is the Thermaltake TH360 ARGB. It is suggested because it is the best value for the money. We called it the Best 360mm AIO CPU Cooler For Ryzen 5 3600 for these and other reasons.
- Excellent performance
- Great design
- A little loud
Deepcool Assassin III
|Noise Level:||29.5 dB|
|Dimensions:||6.34 x 5.51 x 6.5 inches|
|Fan Speed:||1400 RPM|
The Assassin III has seven heat pipes, two strong fans, and a new way of setting up the thermal module. It can compete with all top-tier air coolers because it works so well. The copper base and slightly curved sides make it easy to stick to the CPU.
It has a 54mm clear area for RAM, so it can be used with more things.Because the rim is narrow in the middle and wide on the outside, air can move at its fastest. Noise-cancelling teeth help stop the annoying vibrations that come from noise, which makes it better to use.
Due to its width of 138mm, the Deepcool Assassin III doesn’t get in the way of ATX or M-ATX on GPUs. The outside of the packaging for this design is the same as it is for traditional green and grey products. Compared to other models on the market, this one is a great choice to buy.
Here comes Deepcool’s Assassin III. This big air cooler comes with a lot of extras, like a long-reach magnetic screwdriver, a syringe of thermal compound, a spreading card, an alcohol swab pad, a PWM splitter cable, two RPM reduction cables, a metal case badge, and mounting hardware for most AMD and Intel CPU sockets.
Nickel plating gives the mounting hardware a bright chrome finish, which looks great with the black fans and plastic accent pieces on the cooling tower.
To install a fan, you only need to slip the wire clips into the eyes of the rubberized mounting holes and clip them around each side of the cooler heatpipe towers. The fan clips let you move the cooling fans up and down.
Most memory DIMMs shouldn’t have much trouble with clearance, but if the fan height is changed too much, less air may flow over the lower cooling fins. So, if you want your CPU to cool as well as possible, you should avoid RAM with tall heat spreaders.
- The cooler has seven heat pipes and two big fans.
- Four-step installation process
- 280 watts TDP heat dissipation level
- Units that are old and big
- Hard to put together
|Noise Level:||28.3 dB|
|Dimensions:||14.17 x 6.29 x 4.72 inches|
|Fan Speed:||1700 RPM|
Corsair is a well-known name in the market for PC accessories and parts. They have made a name for themselves by selling high-quality products like Mice, Keyboards, Headsets, Chairs, and much more.
The Corsair H60 is a new cooler that was added to the Hydro Series in the middle of 2018. The H60 is a 120mm AIO Liquid Cooler that does a great job of cooling your Ryzen 5 3600.
It is well made, has a simple design, and makes little noise. It is without a doubt one of the best 120mm coolers on the market.
Corsair is a well-known name in the market for PC accessories and parts. They have made a name for themselves by selling high-quality products like Mice, Keyboards, Headsets, Chairs, and much more. The Corsair H60 is a new cooler that was added to the Hydro Series in the middle of 2018.
The H60 is a 120mm AIO Liquid Cooler that does a great job of cooling your Ryzen 5 3600. It is well made, has a simple design, and makes little noise. It is without a doubt one of the best 120mm coolers on the market.
The H60’s best feature is definitely its simple but effective design. The whole unit is easy to set up because it has simple parts and a clear user manual.
There were no problems with how the RAM, PCIe, and other parts fit together. In fact, it works just as well as other AIO products that cost more, like the Enermax Liqfusion 240 RGB and the Deepcool Captain 240EX. Along with that, the H60 is very quiet, with a noise output rating of only 28.3dbA.
Corsair has become more creative, and the H60 is better in terms of performance and design than the H50 because of it.
- Getting things done well
- Simple to set up
- Good value
- Average performance
Arctic Freezer 34 eSports One
|Noise Level:||28 dB|
|Dimensions:||4.88 x 4.06 x 6.18 inches|
|Fan Speed:||2100 RPM|
This tower cooler is a big surprise. It has a new bionics fan for your convenience. The BioniX F 120 fan has a special thermal coating that makes it work well with CPUs that use 200 W. The air quality is improved by this high-quality fan, which works at 80 CFM and two sounds.
The thermal coating is made in a microtubular shape that makes it possible to directly mount inboard joints. So, it’s easy to put together, heat gets rid of itself better, and there are no air leaks.
High-end CPUs from Freezer 33e Sports One can run at their best. It has advanced technology in its accurate seal damper that cuts air leakage by up to 50% compared to other models. It has a wide range of control, from 200 RPM to 1800 RPM, and it keeps the noise level under control.
The four direct-contact copper heatpipes are aligned and milled flat with the mounting base. They have a wide contact patch that makes a good fit with the CPU’s built-in heat spreader (IHS).
Machine screws hold the mounting brackets directly to the integrated mounting block, and the spring clip mounts snap over the mounting holes on the two 120mm Bionix fans to hold them in place.
From this angle, you can see that both the front and back of the cooling fins have sawtooth edges, which are meant to break up the airflow and make it move around in a choppy way inside the cooler.
Installing the Freezer 34 Esorts Duo is pretty easy and doesn’t take much time. The cooling tower is put together without the fans, so it is very easy to add the 120mm Bionix spinners with the spring clip mounts.
Both fans can be controlled by the same PWM header because they can each “piggyback” on the other. This makes it much easier to change the speed of the fans.
- Nice looks and almost noiseless
- Safe to speed up at 4 GHz
- Easy to put together, and the instructions are clear.
- No special lightning effects
- Intel and ADM only have a limited number of sockets.
CoolerMaster MasterAir MA410M
|Noise Level:||31 dB|
|Dimensions:||6.5 x 9.1 x 6.1 inches|
|Fan Speed:||2200 RPM|
With the introduction of the MasterAir MA410M, CoolerMaster has undoubtedly maintained its dominance in the PC cooling industry. RGB fans will like the MasterAir MA410M because it has a lot of RGB lights.
The performance of the single tower two-fan air cooler is outstanding. With a high fin density and 4x heat pipes, a thermal balance is made to counteract high temperatures. How cool is it that the base plate of the Cooler has a heat sensor that works with the RGB lighting effects?
The CoolerMaster MasterAir MA410M also has CDC2.0, which stands for Continuous Direct Contact technology 2.0. This technology gives the system 45 percent more surface area and makes it easier to get rid of heat by packing the heat pipes tightly together.
The CoolerMaster MasterAir MA410M has 28 addressable RGB lights that are also linked to the thermal sensor. This lets the user instantly change the temperature. The two fans improve performance by letting in the most air and making the least amount of noise.
Some users might find it difficult to set up the CoolerMaster MasterAir MA410M, and others might find the RGB to be too much.
The CoolerMaster MasterAir MA410M is an air cooler made for people who want performance and RGB at an affordable price. We put the MasterAir MA410M on the list of CPU Coolers for the Ryzen 5 3600 because it is the least expensive option.
- Lighting in RGB
- They did a great job.
- Excessive RGB
EVGA CLC 280mm
|Noise Level:||20 dB|
|Dimensions:||17 x 6.4 x 7.8 inches|
|Fan Speed:||2380 RPM|
EVGA has created a new fan design that makes less noise without sacrificing performance. New cooling blocks make it easier for heat to move and for water to flow. It does a great job of cooling and works with AMD, Intel, and upcoming versions.
The sleeved tubing and built-in RGB LED are two other things that make it stand out. It gives you control over the lighting, lets you change the colours, and lets you choose the colour you want.
The new sample has both an AMD AM4 pattern and a legacy pattern. EVGA has flow control monitors that do a good job of keeping an eye on temperature and cooling. It is made of 100% copper and has an RGB LED light system that can be fully controlled.
This model has the same 80,000-hour life span, and its speed ranges from 600 to 2200 RPM. Nanotechnology with Teflon makes this model different from coolers.
Special standoffs fit the integrated support plate of LGA 2011 through 2066 interfaces, and a different set of standoffs replaces the clip bracket of legacy AMD boards if the support plate behind the board has standard threads or nuts.
Users with LGA 115x can attach the support bracket that EVGA gives them to the back of their boards by putting another set of standoffs on the front of the board.The main RGB feature of EVGA’s CLC 280 is the light behind the nameplate.
The EVGA flow control software checks temperatures and makes changes to the fans as needed. Users can set their own fan slopes, but the software might be better than motherboard-based fan control because users can also change the colour of the EVGA logo. The “K” icon forces the machine to run at full speed.
- The best liquid CLC cooler with great quality
- Great job with cooling and voltage regulators
- All ADM and Intel processors could be used.
- With brackets, installation is not safe.
- Noisy in some ways
NZXT Kraken X73 360mm
|Noise Level:||33 dB|
|Dimensions:||18.66 x 7.17 x 5.75 inches|
|Fan Speed:||1800 RPM|
If you don’t want to take any chances with your PC’s cooling and want the best CPU cooler that will fit the ryzen 5 3600 perfectly, then this CPU cooler might appeal to you. It has all the features you could want and is probably the most powerful and best CPU cooler for Ryzen 5 3600.
The most innovative thing about the NZXT Kraken X73 360mm CPU cooler is its ten percent larger infinity cap, which can be used to change the cooler’s orientation depending on how much space you have and where you want to put it.
Well, this is one of my favourite features, so it’s one of the reasons I chose this product for this special list.It also has a good graphic card that is the best graphic card for ryzen 9 3950x. This system is made to work perfectly and is easy to put together.
It has compatible rods that are 4 mm thick, so you shouldn’t have any trouble putting it together.Most people think the best thing about this cooler is its AIO lighting system, which they admire and like.
This LED lighting system looks good and works well all in one piece of equipment. It works with almost every system out there and gives the customer the most convenience and flexibility.This cooler is easy to put together because it has nylon mesh sleeves that are the strongest and last the longest.
This cooler for a Ryzen 5 5600X can have a fan speed of up to 2300 RPM, which moves 73 cubic feet of air per minute and only makes 21 decibels of noise, which is amazing. Its RGBs can also be controlled in simple steps using the CAM interface. With just a few clicks, it is ready to cool down the PC.
- The 7th Gen Asetek pump is very good.
- The effect of the LCD on the CPU block
- The 360mm radiator does a great job.
- Included in the NZXT RGB Aer fans
- CAM software is now good enough to use.
- No direct control of the fan
Factor to Consider when Buying Best CPU Coolers for Ryzen 5 3600
Budget for CPU Coolers
Your budget is the first and most obvious thing. There are many options, but you have to choose based on what you need and how much money you have. But it’s also important that the CPU cooler is of the highest quality for it to work well.
So, you need to set aside a good, enough amount. If you make smart choices when you buy your computer’s CPU, it will get less hot and you’ll spend less money looking for a cooler.
Comparison With Other Coolers
The best coolers for the Ryzen 5 3600 are compared with one another as well as with coolers from other competing brands. We look at their technical specifications as well as their overall performance to determine which one is superior.
We examine every aspect, from the thermal design power (TDP) rating to the quality of the customer service, and evaluate it in relation to other items of the same kind.
Does the thermal design power give any indication as to whether or not it will work with your own computer? Certainly, the ratio of the TDP of the CPU to the TDP of the more relaxed TDP is a significant factor to consider.
The thermal design power (TDP) of the cooler ought to be a little bit later than that of the processor. The two together will provide the ideal mix.
Imagine you are in a room, sitting down, and you turn on your computer. Suddenly, a loud boom hits you in the ear. Your degree of ease is disrupted as a result of this disruption; therefore, noise should be given the highest amount of consideration.
The components of the fan ought to make less noise.
The interoperability of CPU coolers with CPU sockets is given significant consideration during the design process. It is necessary for there to be compatibility between the motherboard, processor, and CPU cooler.
Checking for compatibility with the motherboard socket is important, but there are other variables to consider as well, such as height, radiator size, and bulkiness.
RGB Color Scheme & Type of Cooler
To make a cooler, you must know what kind it is and where it comes from. The cooler’s purpose and, to some extent, its RGB lighting also play important roles.
Coolers for the central processing unit are essential to the effective operation of your processor. If you have been successful in selecting the best alternative for your personal computer, then everything is going to work out wonderfully.
There are occasions when paying a modest price does not turn out to be the best choice. Processors-might be damaged by cooling with a lower price tag. It has been discovered that high-efficiency liquid coolers offer greater performance overall.
FAQs about Best CPU Coolers for Ryzen 5 3600
Is Ryzen 5 3600 good with stock cooler?
Yes, the stock cooler for the 3600 works fine.
Does a Ryzen 5 3600 need a liquid cooler?
Yes! Every CPU needs a CPU cooler. You shouldn’t skimp on cooling because it will affect the life and performance of your computer, but you don’t have to spend a lot.
How hot should Ryzen 5 3600 get with AIO cooler?
With an AIO cooler, your processor shouldn’t go above 80°C. It should stay in the 70s C no matter what kind of load is on it. Your processor’s TDP is 65 Watts, and the highest temperature it can run at is 95c.
Is Ryzen 5 3600 overheat?
Most likely, when you say “overheating,” you mean a temperature of 80–90C under high loads or during benchmarking. This is something that is “wrong” with the Ryzen 5 3600. Even when temperatures are above average, the stock cooler that comes with the Wraith Stealth is not enough to reach 4.2 GHz.
Is the Ryzen 5 3600 a high end CPU?
AMD’s mainstream mid-range processor is the Ryzen 5 3600. It can be overclocked to Ryzen 5 3600X speeds and beyond, but for more extreme overclocks, an aftermarket CPU cooler is recommended.